# generated by Slic3r 1.37.2-prusa3d on Sun Feb  4 16:22:39 2018

[filament:BQ PLA 1.75mm]
bed_temperature = 55
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FB0006
filament_cost = 18.9
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 0
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nEsun PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nEUMAKERS PLA"
filament_settings_id = 
first_layer_bed_temperature = 55
first_layer_temperature = 235
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 25
temperature = 230

[filament:CPE HG 100]
bed_temperature = 90
bridge_fan_speed = 50
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1.15
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #B5F5FD
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 0
filament_notes = "CPE HG 100\n \nTryska: 0,4mm\n \nTeploty: 260-265°C\nBed: 90\n \nPrůtok: 115%\nRetraction distance: 2,1 mm (při 1,5mm nitkovalo)\nRetraction speed: 30 mm/sec\nFan speed: 80% od 2 vrstvy\n \nDefault printing speed: 40 mm/sec\nOutline underspeed: 80%\nSolid infill underspeed: 80%"
filament_settings_id = 
first_layer_bed_temperature = 90
first_layer_temperature = 260
max_fan_speed = 80
min_fan_speed = 80
min_print_speed = 5
slowdown_below_layer_time = 15
temperature = 260

[filament:Carls Purple PLA 1.75mm]
bed_temperature = 55
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FF14E2
filament_cost = 0
filament_density = 0
filament_diameter = 1.7
filament_max_volumetric_speed = 0
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nEsun PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nEUMAKERS PLA"
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 55
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 25
start_filament_gcode = "; Filament gcode\n"
temperature = 210

[filament:ColorFabb Brass Bronze  1.75mm]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1.3
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #B79A39
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 50
first_layer_temperature = 210
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K10 ; Filament gcode"
temperature = 210

[filament:ColorFabb HT 1.75mm]
bed_temperature = 105
bridge_fan_speed = 30
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 10
filament_colour = #ACFDF8
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 105
first_layer_temperature = 270
max_fan_speed = 20
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K45 ; Filament gcode"
temperature = 270

[filament:ColorFabb PLA-PHA]
bed_temperature = 55
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FF14E2
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 15
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 55
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K30 ; Filament gcode"
temperature = 210

[filament:ColorFabb Wood Bamboo 1.75mm]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1.3
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #5A4110
filament_diameter = 1.75
filament_settings_id = 
first_layer_bed_temperature = 50
first_layer_temperature = 210
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 5
slowdown_below_layer_time = 20
temperature = 210

[filament:ColorFabb Woodfil 1.75mm]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1.2
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #5A4110
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 50
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K10 ; Filament gcode"
temperature = 200

[filament:ColorFabb Woodfill 1.75mm]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1.2
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #5A4110
filament_diameter = 1.75
filament_settings_id = 
first_layer_bed_temperature = 50
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 5
slowdown_below_layer_time = 20
temperature = 200

[filament:ColorFabb XT 1.75mm]
bed_temperature = 65
bridge_fan_speed = 50
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #A36FFD
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 90
first_layer_temperature = 240
max_fan_speed = 50
min_fan_speed = 30
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K45 ; Filament gcode"
temperature = 240

[filament:ColorFabb XT-CF20 1.75mm]
bed_temperature = 90
bridge_fan_speed = 50
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1.2
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #000000
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 1
filament_notes = 
filament_settings_id = 
filament_soluble = 0
filament_type = PET
first_layer_bed_temperature = 90
first_layer_temperature = 260
max_fan_speed = 50
min_fan_speed = 30
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K30 ; Filament gcode"
temperature = 260

[filament:ColorFabb nGen 1.75mm]
bed_temperature = 85
bridge_fan_speed = 40
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 10
filament_colour = #ACFDF8
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = NGEN
first_layer_bed_temperature = 85
first_layer_temperature = 240
max_fan_speed = 35
min_fan_speed = 20
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K45 ; Filament gcode"
temperature = 240

[filament:ColorFabb nGen flex]
bed_temperature = 85
bridge_fan_speed = 40
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 10
filament_colour = #ACFDF8
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 5
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = FLEX
first_layer_bed_temperature = 85
first_layer_temperature = 260
max_fan_speed = 35
min_fan_speed = 20
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K10 ; Filament gcode"
temperature = 260

[filament:E3D Edge]
bed_temperature = 90
bridge_fan_speed = 50
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #B5F5FD
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = "List of manufacturers tested with standart PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladeč PETG"
filament_settings_id = 
filament_soluble = 0
filament_type = PET
first_layer_bed_temperature = 85
first_layer_temperature = 230
max_fan_speed = 50
min_fan_speed = 30
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K45 ; Filament gcode"
temperature = 240

[filament:E3D PC-ABS 1.75mm]
bed_temperature = 100
bridge_fan_speed = 30
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #3A80CA
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 13
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 100
first_layer_temperature = 270
max_fan_speed = 30
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K30 ; Filament gcode"
temperature = 270

[filament:Fillamentum ABS 1.75mm]
bed_temperature = 100
bridge_fan_speed = 30
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #3A80CA
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 13
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = ABS
first_layer_bed_temperature = 100
first_layer_temperature = 240
max_fan_speed = 30
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K30 ; Filament gcode"
temperature = 240

[filament:Fillamentum ASA 1.75mm]
bed_temperature = 100
bridge_fan_speed = 30
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #FF8000
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 13
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 100
first_layer_temperature = 265
max_fan_speed = 30
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K30 ; Filament gcode"
temperature = 265

[filament:Fillamentum CPE HG100 HM100]
bed_temperature = 90
bridge_fan_speed = 50
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #B5F5FD
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = "CPE HG100 , CPE HM100"
filament_settings_id = 
filament_soluble = 0
filament_type = PET
first_layer_bed_temperature = 90
first_layer_temperature = 260
max_fan_speed = 80
min_fan_speed = 80
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K45 ; Filament gcode"
temperature = 260

[filament:Fillamentum Timberfil]
bed_temperature = 55
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1.2
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FF14E2
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 55
first_layer_temperature = 190
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K10 ; Filament gcode"
temperature = 190

[filament:Generic ABS 1.75mm]
bed_temperature = 100
bridge_fan_speed = 30
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #3A80CA
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 13
filament_notes = "List of materials tested with standart ABS print settings for MK2:\n\nEsun ABS\nFil-A-Gehr ABS\nHatchboxABS\nPlasty Mladeč ABS"
filament_settings_id = 
filament_soluble = 0
filament_type = ABS
first_layer_bed_temperature = 100
first_layer_temperature = 255
max_fan_speed = 30
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K30 ; Filament gcode"
temperature = 255

[filament:Generic PET 1.75mm]
bed_temperature = 90
bridge_fan_speed = 50
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #B5F5FD
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = "List of manufacturers tested with standart PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladeč PETG"
filament_settings_id = 
filament_soluble = 0
filament_type = PET
first_layer_bed_temperature = 85
first_layer_temperature = 230
max_fan_speed = 50
min_fan_speed = 30
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K45 ; Filament gcode"
temperature = 240

[filament:Generic PLA 1.75mm]
bed_temperature = 55
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FF14E2
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 15
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 55
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K30 ; Filament gcode"
temperature = 210

[filament:PC-ABS E3D 1.75mm]
bed_temperature = 100
bridge_fan_speed = 30
cooling = 0
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #3A80CA
filament_diameter = 1.75
filament_settings_id = 
first_layer_bed_temperature = 100
first_layer_temperature = 270
max_fan_speed = 30
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 15
temperature = 270

[filament:Polymaker PC-Max]
bed_temperature = 120
bridge_fan_speed = 30
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #3A80CA
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 13
filament_notes = "List of materials tested with standart ABS print settings for MK2:\n\nEsun ABS\nFil-A-Gehr ABS\nHatchboxABS\nPlasty Mladeč ABS"
filament_settings_id = 
filament_soluble = 0
filament_type = ABS
first_layer_bed_temperature = 120
first_layer_temperature = 270
max_fan_speed = 30
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K30 ; Filament gcode"
temperature = 270

[filament:Primavalue PVA]
bed_temperature = 55
bridge_fan_speed = 100
cooling = 0
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 100
filament_colour = #FFD1A4
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = "List of materials tested with standart PVA print settings for MK2:\n\nPrimaSelect PVA+\nICE FILAMENTS PVA 'NAUGHTY NATURAL'\nVerbatim BVOH"
filament_settings_id = 
filament_soluble = 1
filament_type = PVA
first_layer_bed_temperature = 55
first_layer_temperature = 195
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K10 ; Filament gcode"
temperature = 195

[filament:Prusa ABS 1.75mm]
bed_temperature = 100
bridge_fan_speed = 30
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #3A80CA
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 13
filament_notes = "List of materials tested with standart ABS print settings for MK2:\n\nEsun ABS\nFil-A-Gehr ABS\nHatchboxABS\nPlasty Mladeč ABS"
filament_settings_id = 
filament_soluble = 0
filament_type = ABS
first_layer_bed_temperature = 100
first_layer_temperature = 255
max_fan_speed = 30
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K30 ; Filament gcode"
temperature = 255

[filament:Prusa HIPS 1.75mm]
bed_temperature = 100
bridge_fan_speed = 50
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.9
fan_always_on = 1
fan_below_layer_time = 10
filament_colour = #FFE130
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 13
filament_notes = ""
filament_settings_id = 
filament_soluble = 1
filament_type = HIPS
first_layer_bed_temperature = 100
first_layer_temperature = 220
max_fan_speed = 20
min_fan_speed = 20
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K10 ; Filament gcode"
temperature = 220

[filament:Prusa PET 1.75mm]
bed_temperature = 90
bridge_fan_speed = 50
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #B5F5FD
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = "List of manufacturers tested with standart PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladeč PETG"
filament_settings_id = 
filament_soluble = 0
filament_type = PET
first_layer_bed_temperature = 85
first_layer_temperature = 230
max_fan_speed = 50
min_fan_speed = 30
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K45 ; Filament gcode"
temperature = 240

[filament:Prusa PLA 1.75mm]
bed_temperature = 55
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FF14E2
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 15
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 55
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K30 ; Filament gcode"
temperature = 210

[filament:Real Filament PETG 1.75mm]
bed_temperature = 80
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #000000
filament_cost = 17.29
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 0
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nEsun PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nEUMAKERS PLA"
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 80
first_layer_temperature = 240
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 25
start_filament_gcode = "; Filament gcode\n"
temperature = 235

[filament:SemiFlex or Flexfill 98A]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 0
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1.2
fan_always_on = 0
fan_below_layer_time = 100
filament_colour = #00CA0A
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 5
filament_notes = "List of materials tested with FLEX print settings & FLEX material settings for MK2:\n\nFillamentum Flex 98A\nFillamentum Flex 92A\nPlasty Mladeč PP\nPlasty Mladeč TPE32 \nPlasty Mladeč TPE88"
filament_settings_id = 
filament_soluble = 0
filament_type = FLEX
first_layer_bed_temperature = 50
first_layer_temperature = 220
max_fan_speed = 90
min_fan_speed = 70
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K10 ; Filament gcode"
temperature = 230

[filament:Taulman Bridge 1.75mm]
bed_temperature = 50
bridge_fan_speed = 40
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #DEE0E6
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 90
first_layer_temperature = 240
max_fan_speed = 5
min_fan_speed = 0
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K10 ; Filament gcode"
temperature = 250

[filament:Taulman T-Glase 1.75mm]
bed_temperature = 90
bridge_fan_speed = 40
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #FD0200
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PET
first_layer_bed_temperature = 90
first_layer_temperature = 240
max_fan_speed = 5
min_fan_speed = 0
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K30 ; Filament gcode"
temperature = 240

[filament:Toms BQ Red PLA 1.75mm]
bed_temperature = 55
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FB0006
filament_cost = 0
filament_density = 0
filament_diameter = 1.65
filament_max_volumetric_speed = 0
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nEsun PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nEUMAKERS PLA"
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 55
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 25
start_filament_gcode = "; Filament gcode\n"
temperature = 210

[filament:Verbatim BVOH]
bed_temperature = 55
bridge_fan_speed = 100
cooling = 0
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 100
filament_colour = #FF14E2
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"
filament_settings_id = 
filament_soluble = 1
filament_type = PLA
first_layer_bed_temperature = 55
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K10 ; Filament gcode"
temperature = 210

[filament:Verbatim PP]
bed_temperature = 100
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 2
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FF14E2
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 5
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nEsun PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nEUMAKERS PLA"
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 100
first_layer_temperature = 220
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 15
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K10 ; Filament gcode"
temperature = 220

[presets]
filament = Prusa PLA 1.75mm.ini
filament_1 = Prusa PLA 1.75mm
filament_2 = Prusa PLA 1.75mm
filament_3 = Prusa PLA 1.75mm
print = 0.20mm Hypercube.ini
printer = Pink Hypercube.ini

[print:0.20mm Hypercube]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 10%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 80
interface_shells = 0
layer_height = 0.2
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 80
perimeters = 3
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 60
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 40
top_solid_layers = 3
travel_speed = 200
wipe_tower = 1
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[printer:Pink Hypercube]
bed_shape = 0x0,195x0,195x190,0x190
before_layer_gcode = 
deretract_speed = 0
end_gcode = M104 S0 ;extruder heater off\nM140 S0 ;heated bed heater off (if you have it)\nG91 ;relative positioning\nG1 E-1 F200  ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-5 X-20 Y-20 F9000 ;move Z up a bit and retract filament even more\nG28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way\nM84 ;steppers off\nG90 ;absolute positioning
extruder_colour = #FFFFFF
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
max_layer_height = 0.25
min_layer_height = 0.07
nozzle_diameter = 0.4
octoprint_apikey = 3802F575B19E4904A1B4625EC780345C
octoprint_host = pink.local
printer_notes = 
printer_settings_id = 
retract_before_travel = 1
retract_before_wipe = 0%
retract_layer_change = 1
retract_length = 4
retract_length_toolchange = 3
retract_lift = 0.4
retract_lift_above = 1
retract_lift_below = 199
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 150
serial_port = 
serial_speed = 250000
single_extruder_multi_material = 0
start_gcode = ;prepare positions\nG21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nG28 X0 Y0 ;move X/Y to min endstops\n\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\n\nG28 Z0 ;move Z to min endstops\n\nM420 S1 ; ensures auto leveling is enabled\nG29; Auto Bed Level\n\nG0 X0 Y-5 F9000 ; Go to front\nG0 Z0.15 ; Drop to bed\nG92 E0 ; zero the extruded length\nG1 X80 E50 F500 ; Extrude 50mm of filament in a 8cm line\nG92 E0 ; zero the extruded length\nG1 E-1 F500 ; Retract a little\nG1 X80 F4000 ; Quickly wipe away from the filament line\nG1 Z0.3 ; Raise and begin printing.\n\nM117 Printing…
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[settings]
autocenter =